matlab-based 3d fem simulator  (MathWorks Inc)

Journal: Sensors (Basel, Switzerland)

Article Title: Wireless Communication Test on 868 MHz and 2.4 GHz from inside the 18650 Li-Ion Enclosed Metal Shell

doi: 10.3390/s22051966

Figure Lengend Snippet: MATLAB RF test setup initial azimuth and elevation planes polar plots for 868 MHz and 2.4 GHz communication with the SMA as radiative element ( A ), the wire loop connected to the SMA ( B ) and the modification on the 3D design for the SMA to insert the simulation RF excitation source ( C ). Since the radiation pattern for dipole and loop antenna are resembling in shape with a torus while 90° offset from each other, the azimuth (az) plane for SMA is similar with the elevation (el) plane for the loop.

Article Snippet: By using the 3D MATLAB simulation, it was possible to illustrate how microwave antennas would be affected by small restrictive metal environments, such as the 18650-cell shell.

Techniques: Modification

Journal: Sensors (Basel, Switzerland)

Article Title: Wireless Communication Test on 868 MHz and 2.4 GHz from inside the 18650 Li-Ion Enclosed Metal Shell

doi: 10.3390/s22051966

Figure Lengend Snippet: MATLAB signal attenuation simulation by using the Three-ray and Free space models for 868 MHz and 2.4 GHz for following the scenario described in ( A ), resulting in a computed reflection coefficient versus distance for the concrete ground and ceiling such illustrated in ( B ).

Article Snippet: By using the 3D MATLAB simulation, it was possible to illustrate how microwave antennas would be affected by small restrictive metal environments, such as the 18650-cell shell.

Techniques:

Journal: Sensors (Basel, Switzerland)

Article Title: Wireless Communication Test on 868 MHz and 2.4 GHz from inside the 18650 Li-Ion Enclosed Metal Shell

doi: 10.3390/s22051966

Figure Lengend Snippet: MATLAB 3D radiation pattern simulation for the cell’s shell radiative structure integrating the SMA and the wired loop for 868 MHz and 2.4 GHz over the ground plane in a vertical orientation.

Article Snippet: By using the 3D MATLAB simulation, it was possible to illustrate how microwave antennas would be affected by small restrictive metal environments, such as the 18650-cell shell.

Techniques:

Journal: Sensors (Basel, Switzerland)

Article Title: Wireless Communication Test on 868 MHz and 2.4 GHz from inside the 18650 Li-Ion Enclosed Metal Shell

doi: 10.3390/s22051966

Figure Lengend Snippet: MATLAB 3D radiation pattern simulation for the cell’s shell radiative structure integrating the SMA and the wired loop for 868 MHz and 2.4 GHz over the ground plane in a horizontal orientation.

Article Snippet: By using the 3D MATLAB simulation, it was possible to illustrate how microwave antennas would be affected by small restrictive metal environments, such as the 18650-cell shell.

Techniques:

Journal: Sensors (Basel, Switzerland)

Article Title: Wireless Communication Test on 868 MHz and 2.4 GHz from inside the 18650 Li-Ion Enclosed Metal Shell

doi: 10.3390/s22051966

Figure Lengend Snippet: MATLAB signal attenuation simulation by using the Three-Ray and Free space models for 868 MHz ( A ), and 2.4 GHz ( B ), between the concrete ground.

Article Snippet: By using the 3D MATLAB simulation, it was possible to illustrate how microwave antennas would be affected by small restrictive metal environments, such as the 18650-cell shell.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: ( A ) FBD of the 3D MATLAB topology simulation utilising the external Sections, C and D, of the ITAP, dimensions of 85 mm by 14 mm by 14 mm with applied loads, ( B ) Vertical model using F x and F y 95% volume of material, ( C ) Vertical model using F x and F y 55% volume of material.

Article Snippet: The MATLAB 3D simulations provide the most detailed results.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: Visual comparison between topology simulation of Section C and D of the ITAP at 50% volume of material, ( A ) one solid model using ANSYS’s control, ( B ) 2 sections joined together using ANSYS’s simulation controls, ( C ) 2D MATLAB simulations with only the shear force being applied to identify the potential areas of material reduction, ( D ) 3D MATLAB standard model, ( E ) 3D MATLAB vertical model, ( F ) 3D MATLAB horizontal model.

Article Snippet: The MATLAB 3D simulations provide the most detailed results.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: Visual comparison between topology simulation of Sections C and D of the ITAP at 50% volume of material, ( A ) one solid model using ANSYS’s control, ( B ) 2 Sections joined together using ANSYS’s simulation controls, ( C ) 3D MATLAB standard model, ( D ) 3D MATLAB vertical model.

Article Snippet: The MATLAB 3D simulations provide the most detailed results.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: Simulated results of the 2D MATLAB topology simulations identifying the theoretical areas of material reduction of 50 to 95%.

Article Snippet: These two positions of material reduction are concordant with both the ANSYS and 2D MATLAB simulations as well as all three models of the 3D MATLAB simulations.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: ( A ) FBD of the 3D MATLAB topology simulation utilising the external Sections, C and D, of the ITAP, dimensions of 85 mm by 14 mm by 14 mm with applied loads, ( B ) Vertical model using F x and F y 95% volume of material, ( C ) Vertical model using F x and F y 55% volume of material.

Article Snippet: These two positions of material reduction are concordant with both the ANSYS and 2D MATLAB simulations as well as all three models of the 3D MATLAB simulations.

Techniques:

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: Visual comparison between topology simulation of Section C and D of the ITAP at 50% volume of material, ( A ) one solid model using ANSYS’s control, ( B ) 2 sections joined together using ANSYS’s simulation controls, ( C ) 2D MATLAB simulations with only the shear force being applied to identify the potential areas of material reduction, ( D ) 3D MATLAB standard model, ( E ) 3D MATLAB vertical model, ( F ) 3D MATLAB horizontal model.

Article Snippet: These two positions of material reduction are concordant with both the ANSYS and 2D MATLAB simulations as well as all three models of the 3D MATLAB simulations.

Techniques: Comparison, Control, Shear

Journal: Micromachines

Article Title: The Micro Topology and Statistical Analysis of the Forces of Walking and Failure of an ITAP in a Femur

doi: 10.3390/mi12030298

Figure Lengend Snippet: Visual comparison between topology simulation of Sections C and D of the ITAP at 50% volume of material, ( A ) one solid model using ANSYS’s control, ( B ) 2 Sections joined together using ANSYS’s simulation controls, ( C ) 3D MATLAB standard model, ( D ) 3D MATLAB vertical model.

Article Snippet: These two positions of material reduction are concordant with both the ANSYS and 2D MATLAB simulations as well as all three models of the 3D MATLAB simulations.

Techniques: Comparison, Control